SRT Engineering Q&A Tonight @ SRTForums 6-8PM EST

[JayC]

Sorry for the late notice but I wanted to let everyone know that there will be a Q&A session tonight with members of the SRT Team.

Here is a link to the thread where the discussion will be taking place.

Everyone is invited to drop by the thread and see what the SRT guys have to say!

[Rambit]

Originally Posted by JayC

Sorry for the late notice but I wanted to let everyone know that there will be a Q&A session tonight with members of the SRT Team.

Here is a link to the thread where the discussion will be taking place.

Everyone is invited to drop by the thread and see what the SRT guys have to say!

I thought they came off very disinterested and I think there was only a couple of them participating when they did the last one here in December. I'm going to keep slugging away with the brake thing though.

Rambit

[glhs837]

Well, darn, they guys from Chargerforums are going to be bummed. Guess Id better get a list of what they want to see asked.

[Rambit]

Those SRT 4 guys have already flooded the thread with the same old questions. It should never have been opened up till a few minutes before 6 PM. Good luck getting a question in sideways tonight. It's already shaping up the same as the first disaster...stage I, stage II, stage III, what oil should I run, and all that. Too bad, maybe I'll just watch Barrett-Jackson.

Rambit

[Nevermore]

Why don't the moderators have a predefined list of questions, that were approved in advance, and then have the SRT team answer them?

If I hear that one SRT-4 guy ask about extending his MAP with a prebuilt harness one more time....

Any way, I would think that a little pre-planning would work wonders.

I do have one question for the 300c forum members:

Is there any way to change from a speed density to a mass air sensor?
(Without having to create my own computer?)

-Nevermore

[HEMEEE]

Originally Posted by Nevermore

Why don't the moderators have a predefined list of questions, that were approved in advance, and then have the SRT team answer them?

If I hear that one SRT-4 guy ask about extending his MAP with a prebuilt harness one more time....

Any way, I would think that a little pre-planning would work wonders.

I do have one question for the 300c forum members:

Is there any way to change from a speed density to a mass air sensor?
(Without having to create my own computer?)

-Nevermore

We tried doing preplanned questions here last time, but the SRT team prefers spontaneity. problem is, not everyone can participate at the assigned time, or as in this case, on such short notice. But having organized in advance did help us try to address the questions of those not present, although the team only wanted one question per person. The other issue is that these sessions are open to other forums, so no way to moderate those questions in advance.

As for your air sensor question, please ask in a different thread Thanks

[Rambit]

It's actually not going too bad tonight. They seem to have a lot more interest in it this time. I'm impressed.

Rambit

[amant]

The Q&A session is going on right now over at http://www.srtforums.com right now. So if any of you are registered over there (I'm not) go and ask the brake fix question again, again,again you know kind of like clean rims again, again or better yet squeal,squeal, squeal, squealllllllllllllllllllllllllllllllllllllllllllll lllllll or whatever questions you may have.

amant

[Rambit]

Originally Posted by amant

The Q&A session is going on right now over at http://www.srtforums.com right now. So if any of you are registered over there (I'm not) go and ask the brake fix question again, again,again you know kind of like clean rims again, again or better yet squeal,squeal, squeal, squealllllllllllllllllllllllllllllllllllllllllllll lllllll or whatever questions you may have.

amant

I asked amant. There may be some hope coming...
New brake pads for TSB available yet ??

Rambit