Fault Codes P0046 and P0673 - CRD Turbo

[Boro al]

The solenoid sounds like the turbo actuator that operates the variable vanes and this is part of the turbo and not a seperate part.

I think the boost is being pushed too far and could cause other issues.

[UK CHRYSLER 300C]

There is a guy/company on the net I found that states he can reset the actuators....I don't know how but he says he can...When I finally got that turbo off the guy/idiot the customer got it from said he had to have the old turbo complete with actuator as it had to be re-programmed but the new turbo came with a brand new actuator on it

[Simon@thecustom300cshop]

I would just like to point out that the map the OP (Robbiekova) has installed on his car that is causing him problems is NOT one of our Stormtech maps.

I understand the OP had asked the tuners directly to create a further enhanced map to try and get even more power out of his car. To my knowledge the map he has had made could not have been tested on his car as he lives on another continent.

The Stormtech maps we had developed especially for us were thoroughly tested on the dynamometer to ensure they are within safe engine parameters.

[robbiekova]

Yes Simon is correct. Just me trying to get more, sorry Simon did not mean to make people think it is your maps that caused the issue.

Just wish to confirm that your performance maps have caused no issues.

Thanks

[Simon@thecustom300cshop]

Originally Posted by robbiekova

Yes Simon is correct. Just me trying to get more, sorry Simon did not mean to make people think it is your maps that caused the issue.

Just wish to confirm that your performance maps have caused no issues.

Thanks

No problem Rob, I just didn't want people putting 2 and 2 together and coming up with 10 lol

BTW, the problem sounds like it is over boosting a little to me. Do you not have any companies in Australia that could set it up on a dyno for you?

[jackwalton]

Originally Posted by Simon@thecustom300cshop

No problem Rob, I just didn't want people putting 2 and 2 together and coming up with 10 lol

BTW, the problem sounds like it is over boosting a little to me. Do you not have any companies in Australia that could set it up on a dyno for you?

Simon,

I've just remapped my 300C with your Viezu V-Switch, (Yesterday) and I am well impressed.
Thanks for your help and advice.

Jack

[Simon@thecustom300cshop]

Originally Posted by jackwalton

Simon,

I've just remapped my 300C with your Viezu V-Switch, (Yesterday) and I am well impressed.
Thanks for your help and advice.

Jack

Glad you are a happy Jack, now start saving for some new rear tyres lmao

[jackwalton]

Originally Posted by Simon@thecustom300cshop

Glad you are a happy Jack, now start saving for some new rear tyres lmao

Yes they do smoke a bit ?http://www.300cforums.com/forums/images/smilies/new/angryfire.gifhttp://www.300cforums.com/forums/images/smilies/new/angryfire.gif

[AgentE]

Originally Posted by robbiekova

Over the weekend took the car for a bit of a drive and noticed something when hard on the accelerator after I had a Viezu tuning done to it.

When accelerating hard 1st, 2nd is all good, switches to 3rd and at about 3,000 revs the car bunny hops until about 3,250 revs then all good again. Car seems like it is fighting to push through, but something is limiting. Up till then it is bloody quick and straight after the same, just that 250 to 500 revs when it seems to struggle through.

Checked for fault codes and P0046 and P0673 come up. Anyone had these before and know what they are and actually mean and are they simple fixes?

Thanks

WHOLE THE SAME !!!
When i write performance map i really impressed.That day everythings was good.
3 days ago i tried my car on highway.When i went to other city my car was really good.
When i come back my city something was wrong.
(When accelerating hard 1st, 2nd is all good, switches to 3rd and at about 3,000 revs the car bunny hops until about 3,250 revs then all good again. Car seems like it is fighting to push through, but something is limiting.)
When i go on D mode about 120km/h if i full throttle on 140km/h bunny hops also same story on 180km/h...
in addition to these when i be on the move if tachometer reduce about 1000 rpm then when i try to accelerate again the car was shaken (maybe i didnt explain that for example manual gear car when you on 5th gear but your car 20km/h )
I contact wtih Viezu.They said pls check DTC Codes.And i saw P0046 !!!
Tomorrow i hope i should apply algorithm.(once test drive check code if i see again i'll back stock mode.)
Thanks

[UK CHRYSLER 300C]

Originally Posted by jackwalton

Yes they do smoke a bit ?http://www.300cforums.com/forums/images/smilies/new/angryfire.gifhttp://www.300cforums.com/forums/images/smilies/new/angryfire.gif

Not as much as this.....lol

Bloody ipad not showing my sig of the burnout.....grrr