Chrysler 300C & SRT8 Forums banner

Discussions Showcase Albums Media Media Comments Tags Marketplace

1-20 of 34 Results
  1. Cooling
    Thought I would share the oil, trans & power steering cooler upgrades I installed on my 300C Ya'll enjoy.
  2. General Discussion
    Hi I have an 06 chrysler 300c and my rear end broke. So I have a tow truck come to tow me home. Well as he was starting to pull it up on the flat bed. We realized he did not take the car out of park. Is my tranny going to be ok??:(
  3. 1st Gen SRT8-Specific Problems/Dealer Service
    Hey guys I'm at a loss. Took my 09 300c 5spd in to local mechanic to find issue with limp mode. ABS ESP BAS lights were illuminated and vehicle was stuck in limp mode. Long story short, it was the reluctor rings on the cv axle half shaft that were bad. Changed cv axles then the code cleared. I...
  4. Transmission
    I live in south Texas, and the weather went from the 60's to 80's down into the 30's. The day after the temp dropped, I went to start my vehicle. I have a 2012 300C. The transmission was rebuilt about 16 months ago. I had driven without any problems the night before. Anyway, I start the...
  5. General Discussion
    Ok I have and 06 Chrysler 300 with 5.7 and a nag1 transmission and wondering if the 8 speed transmission is compatible with swapping? I already have 2020 scat pack rear end getting installed jus wondering before I start the project if the transmission would fit
  6. General Discussion
    Hello all, someone I know is selling an 08 Chrysler 300 5.7 AWD with a bad transmission. I have previously owned and worked on an 07 charger 5.7, so I'm fairly familiar and competent with the mechanical work that goes with them. My question is: is the nag1 in the 5.7 AWD the same/interchangeable...
  7. General Discussion on Issues / Trouble Shooting
    2007 300C RWD 5.7 HEMI Before all the transmission problems the abs,traction and the other yellow lights were going on and off for 2 weeks. So I had the transmission lockout issue. Where the spring tab breaks. I was in an area without internet access.. So I didn't know how to fix it. Shifter...
  8. Transmissions, DriveShafts, Rear Ends
    I have a 2012 chrysler 300c awd. Got the car and it wouldn't go into drive or reverse sometimes it worked sometimes didn't. So changed transmission with a good one thinking might be issue because transmission pan was rusted out. Changed it with no luck. Sometimes it'll go in drive and let go of...
  9. General Discussion
    Hello everybody, I have a 2006 300 touring, 3.5 and am having issues with it Recently. I just bought the car and it ran fine but needed a drive shaft, I bought a driveshaft and had someone install.. a few days later I’m going to leave the driveway and the car just all the sudden slows to a stop...
  10. Transmission
    That’s basically it. I’m aware of an O2 sensor being bad but would that cause the engine to run high between 2nd and 3rd? 2007 300C TIA
  11. Transmission
    Will a 2014 srt8 charger transmission bolt on to a 2006 Chrysler 300c ? Will I need to change anything or is it plug and play . I’m new
  12. 2nd Generation Chrysler 300 Discussion
    I'm looking for a NAG1 expert on Long Island, NY who can resolve a problem that has shown me that most shops simply don't understand. Keep in mind that when this started happening a couple of months ago, I immediately had the fluid and filter changed. No difference. Adaptive learning has been...
  13. 1st Gen SRT8-Specific Problems/Dealer Service
    Hey there, Im really trying to diagnose this damn issue and I'm not sure if anybody else may encountered the issue. I've replaced front and rear couplers, I've just replaced the trans fluid at the dealer, I did the dif fluid which wasn't bad, and the u joint on the drive shaft. I'm just continue...
  14. Transmission
    I have a 2015 Chrysler 300 touring. I was just testing out how fast I can take it but it stopped at 193 and on the 5th gear (it's an 8 speed automatic) and I have no clue why. I've searched everywhere and can find that issue anywhere. The rpm just stops at around 3500 to 4000 and the speedometer...
  15. General Discussion on Issues / Trouble Shooting
    I have a 2006 Chrysler 300c 5.7 hemi, when I try to put it into drive it won’t go into gear. When I go from park to reverse it goes into reverse. When I pull it into neutral from reverse it stays in reverse and goes into neutral when I pull the gear selecter into drive. Stays in neutral when I...
  16. 2nd Gen SRT8- Body & Interior
    Hi all Anyone know where I can pick up a new carbon fibre dash trim for around the gear selector? Looking for RHD spec, Australia. Should they be different to LHD. Old one is gone, currently has a 3m carbon wrap.
  17. 5.7 V8 Engines
    Over the weekend I installed rear disc brake rotors, pads and rear passenger cv axle. After everything was finished I got in the car. Once started (in park) the instrument cluster displays "Standby" and when I push on the brake pedal, there's a ticking noise coming from the center console. I...
  18. General Discussion on Issues / Trouble Shooting
    I have a 2006 dodge magnum SRT8 6.1L. I have the tranny out to replace a leaking front input shaft seal, or torque converter seal. When I pulled out the torque converter and seal, there was a bronze looking bushing in there behind the seal; the front pump bushing. Stupid me when trying to get...
  19. CRD Engine / transmission
    Good morning, I have the following problem: the gear selector moves without any problem among gears (P, R, N, D), but the problem is that the gears don´t shift as they should in reality - sometimes it shifts without a problem for the first time and sometimes I have to shift with gear selector...
  20. General Discussion on Issues / Trouble Shooting
    Hello to all I just recently joined this forum, Being a owner of Chrysler and faced with problems the entire time I have had my 300 . All started Feb 19 , 2012 Purchased my 2009 Chrysler 300 touring 3.5 l rwd Being obviously the Second owner The odometer was exactly 28,009 km. in the 3...
1-20 of 34 Results
Top